Buy fishing tackle TV. How to make a TV for fishing a fishing screen with your own hands

Dear fishermen! Earlier on this page there was an article about how to make a TV for fishing or fishing screen do it yourself. But due to the fact that this type fishing prohibited by the law of the Russian Federation, we received a letter with the following content:

In accordance with Part 7 of Article 15.1 of the Federal Law of July 27, 2006 No. 149-FZ “On Information, information technology and Information Protection" we notify that on the basis of the decision of the court / authorized federal executive body (Stanovlyansky District Court - Lipetsk Region) dated 19.12. allowing to identify sites on the Internet containing information, the dissemination of which in Russian Federation prohibited”, registry entry number 607031-RI due to the fact that this information contains information, the distribution of which in the Russian Federation is prohibited by a court decision.

Information is posted on the method of manufacturing and upgrading the fishing "TV", which is a prohibited fishing gear and a method of mass destruction of biological resources, recognized as prohibited on the territory of the Russian Federation.

From the moment you receive this notice, you must immediately delete information whose distribution is prohibited in the Russian Federation.

I don't even know why so many years have been chasing fishing tackle like fishing TV. You won’t catch a big catch on it, except perhaps in your ear, it doesn’t cause any severe damage to the fish, it doesn’t pollute the ecological environment, in general, the catch is not much different from fishing with a fishing rod or spinning rod, except that you can’t catch a large catch on a fishing TV, but definitely that fishing in this case will be a great vacation for many.

What is a fishing TV:

Fishing TV is a rectangular or square frame. Its dimensions are usually 1.5 by 1.5 meters or 1.5 meters long and 1.0 meters wide, depending on the depth of the reservoir at the casting site. Many craftsmen select sizes that correspond to previously looked after places.
The upper part of the TV (float) is an ordinary wooden rail or bamboo stick, one and a half meters long. Lacquered to reduce swelling in water. The lower part (weight) is a heavier material so that the screen sinks to the bottom. Most often it is a metal bar.
On the finished frame, the mesh fabric is fixed with a strong thread. At the beginning of a bamboo stick or rail, one end of the thread is fixed, the mesh cells are tied in several places with a nylon thread to the end of the rail. Same with the metal rod.
In the side part of the canvas, a nylon thread or cord runs in a spiral from a bamboo stick to a metal bar, without missing a single cell.
A cord or nylon thread is tied to the upper wooden rail in the middle, to which a foam float is attached, so that you can see the place on the surface of the water where the fishing TV is installed.
Fishing net is considered to be more catchy than silk thread or twisted rope, but the life of the fishing line net is less than that of the net cloth.

The size of the caught fish depends on the size of the cell, if the cell is 18 mm, then this is a medium-sized catch, such a fish will be good as a bait for a predator. And if 24 mm, then it will be larger. Whatever method you fish with, don't forget to feed your fishing grounds. Then your fishing trip will end with an excellent fish soup and a wonderful dinner in nature. Please do not use prohibited fishing methods such as fishing TV or fishing screen.

Why is it forbidden to use fishing TV:

Refers to methods of mass extermination of biological resources
It kills fish if it is in the water without the supervision of a fisherman, that is, if your fishing screen is carried away by the current, a huge number of fish will suffer, it will simply get stuck and rot alive.

What methods of installing fishing screens are prohibited:

From the shore, when a rope is tied to a stick or pole, with which, after the catch, you can deliver the TV to the shore.
From the boat, when the fishing screen is lowered by a nylon thread with a float to the desired installation location.
Other, all sorts of ways to install screens and catch fish in open water.

It is also prohibited to fish in holes in winter period, but for this method, fishing scarves are more often used. The scarf is similar to a TV, but the canvas has a triangular shape and instead of a wooden lath, a float is installed at the top point.

Attention! Fishing TVs and screens are prohibited by the law of the Russian Federation.

A good angler in his arsenal has many varieties of gear, lures and other accessories for any season. fishing. In addition, any professional angler needs to have such a fishing device as a fishing screen in their fishing gear. Many fishermen are familiar with it since early childhood. It is easy to make and does not require a large investment to make it. Since not all fishermen have enough money to buy it in a fishing store, let's see how you can make a homemade fishing screen or, as it is called in another way, a fishing TV, right at home and save your hard-earned money.

In fact, using a fishing screen big catch you should not wait, but this device is very fond of both adult fishermen and children. With it, you can catch enough fish in your ear or just fry, but the most important feature of the fishing screen is that it does not pollute the fish habitat, that is, the reservoir, and does not harm the fish. You can catch about the same amount of fish with this device as with a spinning rod or a fishing rod, but the only difference is that you cannot catch large fish with it. After all, the pleasure is not in what kind of fish you catch, but in the very process of fishing.

Materials for a homemade fishing screen

If you haven't changed your mind and still want to make a fishing screen, let's get started. This will require the following materials:

float made of foam;
a metal bar or, as they call it in another way, a bar;
wooden rail;
fishing line;
mesh fabric;
kapron thread or cord.

Stages of manufacturing a fishing screen

To make a fishing screen, you will need a square or rectangular frame. You can choose the sizes by eye. The dimensions depend on the depth of the reservoir and the place where you are going to throw it.
The float or top of the screen is made from a bamboo or wooden stick that needs to be varnished. This process is necessary so that the wooden structure does not swell in water. You can, of course, not varnish, but this can subsequently destroy the structure. The weight or lower part must be made of heavy materials to immerse the screen to the bottom of the reservoir. For the bottom of the fishing screen, you can use a metal bar. Then we cut the canvas from the grid to the size of the prepared frame at the bottom and upper parts cloth and pull the cord. This must be done on each cell, or at least through one.
When you have a cooked frame, you need to fasten a mesh fabric to it using a strong thread. This is done in the following steps: first, we fix the end of the thread to the bamboo stick, then the mesh cell must be tied in other places with the help of a thread. And so it continues until the mesh canvas is completely fixed to our frame. A similar procedure must be done with a metal twig.
After that, from the side of the canvas, we skip the prepared thread in the form of a spiral, starting from a stick and ending with a bar, while not a single cell can be skipped. This is necessary in order to relieve the tension of the net under water, and during the raising of the net to the surface of the water.
We fix the cord on the stick in the middle, then we hook the float to it, for the manufacture of which foam plastic was used. The presence of a float is necessary in order to know where the fishing screen is located.

On a note: a net made from fishing line is the most catchy compared to a net made from twisted rope, while a net that was made from fishing line has a shorter service life than a net cloth.

When fishing on a fishing screen, it is worth knowing a few tricks, which we will discuss below. The size of the fish caught depends on the size of the cell used. When using a 18 mm cell, a small fish comes across that is suitable for bait when hunting a predator. If you use a 24 mm cell, then there is a chance to catch big fish. Whatever cell you use, you always need to feed the fish, then you will get good catch for fish soup and a wonderful outdoor recreation.

This unsightly homemade fishing tackle is very popular among fishermen. People call it a "TV" because it is shaped like a TV screen.

How to DIY

The fishing screen has a very simple design, consisting of a rectangular frame measuring 1.5x1.5 meters. The frame is made of any material: wood, metal, etc. The frame is made in such a way that the screen is securely held as in standing water, as well as in the course. This tackle requires a load, so many anglers weld a frame of metal rods with a diameter of 6-8mm. The design turns out to be moderately light and interesting: not as massive as it turns out from wooden beams.

A woven mesh fabric is attached to a metal or wooden frame. We can immediately say that the thinner the material of the net fabric, the more attractive tackle for fish. The canvas is attached to the frame with a strong artificial thread. In this case, it is necessary to fix each cell of the canvas.

There is one caveat here: do not stretch the canvas. The more it sags, the more effective the tackle will be. Loops are formed at the corners of the screen for applying a powerful rope to them, with which the screen is pulled out of the water. The design is as follows: a piece of rope, up to 1.5 meters long, is tied to the loops, after which all four ropes are tied into one knot, and a longer rope is tied to this knot. It allows you to pull the fishing screen out of the water without problems.

A load is attached to the bottom of the canvas, which sags the mesh, otherwise the screen will not be effective without it.

The fishing screen is cast either from the shore or from a boat. Moreover, the technology of its use is such that it must be suspended in the water column, otherwise there will be no sagging of the network fabric. This is easy to organize from a boat, but if you fish from the shore, you will have to experiment a little. You can tie a long stick to a rope and use it to lower the screen into the water.

Screens can be used for catching small fish (for live bait) or large. To catch live bait, you should put a canvas with small cells (up to 20mm), and for catching large fish, you should put a canvas with cells of 35mm or more. To additionally lure fish, you can tie a bait to the bottom of the screen. It can be cake, bread crusts, etc.

Some anglers basically fish exclusively with rods for their own pleasure. And others prefer to take it easy and use a fish screen that is easy to make and use, and inexpensive. In this article, you will learn how to make a DIY fishing screen, because many fishermen prefer to make their own fishing screen.

A fishing screen is a popular rectangular or square-shaped device that belongs to artisanal fishing gear. Because of its shape, it is also called "fishing TV". The fishing screen allows you to catch fish without difficulty, especially small ones (for bait).

Fishing screens are best installed on reservoirs, ponds, rivers, where there is no current, and especially on warm spring and summer days. But this does not mean that in winter it is impossible to catch in this way. There is a so-called fishing scarf, the principle of its manufacture is the same, but it has a triangular shape, which falls into the hole and a float is used as a wooden block.

fishing screen

You can install such gear in two ways:

on open water from a boat or boat;
near the coast, from the bridge, from the dam.

It is much easier to catch fish from a boat, as you can choose any place to catch a fish in a pond and calmly throw the tackle behind a strong thread with a float. In any case, installing a TV from a boat will be more effective than from the shore because of the reeds.

You have to additionally make a wooden pole with a rope. At the end of the rope, attach a hook that could catch on a fishing line or cord floating in the water, and thus get the TV.

Legality of fishing

Fishermen are fined for using fishing screens. Although this method does not provide for a large catch of fish, as with the help of other gear or nets, the regulatory authorities still strictly monitor the conservation of most fish species.

Sometimes fishermen think that since they have small do-it-yourself fishing TVs, this does not concern them. But everyone should remember that during the spawning period, you need to refrain from fishing.

During this period, prepare all your belongings in order for the new season.

Screen device

Instructions for making a fishing screen

Every real fisherman will sooner or later think about how to make a TV for fishing with his own hands. To do this, he will need the following materials:

float made of light material (polystyrene);
plastic tube, wooden block (bamboo stick);
mesh fabric;
cargo (metal bars);
fishing line, kapron threads, cord.

Let's consider in more detail step by step instructions how to make a screen for fishing:

Usually the width and length of the fishing TV is 1.5 meters. But depending on the depth of the reservoir, the length of the screen is sometimes increased;
In the manufacture of the upper part (float), a plastic sealed tube or a flat wooden block coated with waterproof varnish or paint is used;
As the lower part, a load of metal rods is used so that the screen can be easily lowered to the bottom of the reservoir. Some fishermen additionally attach bait in the center of the screen;
The next step is to prepare the mesh fabric, which must match the size of the frame. The dimensions of the cells of the mesh fabric depend on the purpose of the purpose and the use of such gear. As a rule, they have sizes from 15 to 50 mm;
The finished mesh fabric is attached to the upper and lower parts of the frame with a strong nylon thread that passes through each mesh cell. For effective fishing, the net cloth should be made of thin high-quality threads so that the screen is not visible in the water, and also not pulled strongly on the metal frame;
On both sides of the upper part of the frame, two nylon or fishing lines are attached, which smoothly turn into a cord or thick fishing line with a size of at least 0.7 mm, at the tip of which a foam plastic float floating on the surface of the water is tied. This is necessary in order to determine the location of the TV and find out if the fish is caught;
DIY fishing screen is ready to use. Although such tackle does not differ in durability, it does not cause harm to other fish and does not pollute water resources.

A fishing screen is a small home-made fixed net, which is commonly called the simple word “TV”. This network got its name due to the fact that in its shape it resembles a flat-panel TV.

The screen itself is a simple mechanism. First, a TV frame is made - a rectangular frame.

Its sides should reach an average of 1.5-2 meters in length. The top of the screen can be made from a regular rail or a wooden block.

The lower one is heavier from a stick (you can also use a rail). The upper and lower composite screens provide its reliable fixation in still water and in small currents.

A network fabric is attached to the finished frame with a strong thread. The thread must be fixed at the beginning of the stick (slats) and begin to put the cells on the thread and tie it to the stick.

Here it is worth remembering that the smaller the thickness of the netting thread, the more fish you can catch. Fishing nets are more catchy, but they are not so durable.

Net fabric is made of braided cord or twisted rope.

Each cell of the canvas is tied to the edge in a spiral. The thread is threaded from the top to the bottom, without missing a single cell, thereby stretching into a straight line. The network will work the more efficiently, the lower the tension of the net fabric. Also, the length of the thread between the top and bottom will directly depend on the height of the fishing screen.

On a centimeter from the edge of the rails on both sides, loop knots must be made to secure the ends of the screen and the net thread. A load is attached to the bottom of the assembled canvas.

In the upper part, a fishing line with a float is usually attached. It will be on the surface of the water and indicate that a fish has been caught.

You can install a rigid float in the form of a stick dried and painted with waterproof paint. The fishing screen is installed in two ways: it is lowered on a fishing line or rope from a boat, or it is cast from the shore.

At one end of the screen, a long rope is tied, with which the structure can be easily pulled ashore. If several fishing screens are installed, be sure to mark in some way the place where they are located, so that later they can be easily found.

A computer screen is measured in inches and the number of pixels that can be displayed horizontally and vertically on the display. The physical size in inches cannot be reduced, but you can set a smaller number of pixels, i.e. reduce the screen resolution, it is quite possible.

To do this, follow these steps.

Right-click on an empty space on your desktop. In the drop-down menu, select the "Personalization" item (in the Windows XP operating system and earlier versions, this item is called "Properties").

You will see a component that allows you to configure appearance screen. Click on the "Display Options" section.

In the window that opens, move the "Resolution" slider to the left. In this case, below will be displayed to what value the screen resolution has decreased.

For example, at first it was 1280 × 800, and now it is 640 × 480 pixels (dots). Click "OK" to save your changes.

The screen will turn off for a few seconds and then turn on with the new resolution. Windows will ask you to confirm the new display settings within 10 seconds, otherwise they will return to the previous ones.

Click "OK" if you are satisfied with them. It is safest for your eyesight to use the screen at the maximum resolution of the monitor.

vkontakte how to make a big screen

Fine-mesh nets (with a mesh of less than 20 millimeters) are used to catch small fish. The larger the network, the large sizes fish can get caught.

The fishing screen is rarely used as an independent tackle. It usually performs auxiliary functions.

how to make a fishing net

www.kakprosto.ru

Proportions of rice and water for the perfect dish.

The most delicious barbecue recipe ever! TOP - 10 most mushroom places of the Samara province. Awning on boat pvc with your own hands.

Catching pike on a twister. As a rule, fishing screens are used in the summer, when nothing interferes with their installation.

How to screen fish or the "grandfather" method

They are installed on ponds, in bays, in backwaters of rivers, but the use of screens on the course is quite problematic. In conclusion, I would like to say that fishing screens are part of passive fishing, which many fishermen do not tolerate in principle, preferring active types of fishing, as well as fishing float rods or feeder gear.

Simplicity of design, the ability to assemble it yourself, cheapness when buying, for example, in my region they offer screens from r for the product, this attracts fishermen. Now let's talk about ease of use. It would seem that throw the screen into the water and wait for the catch. Of course, having previously secured to the shore. Although they are not so obvious and require a margin of time.

A set of lures 34 items. What you need to know when going fishing Algae and fish bait Let's talk about the lack of bite Aromatic bait - choose according to your taste Picker's equipment and bait when fishing Let's talk about bait and its preparation.

The fishing screen has a very simple design, consisting of a rectangular frame measuring 1.5x1.5 meters. The frame is made of any material: wood, metal, etc. The frame is made in such a way that the screen is securely held both in still water and in the current. This tackle requires a load, so many anglers weld a frame of metal rods with a diameter of 6-8mm. The design turns out to be moderately light and interesting: not as massive as it turns out from wooden beams.

A load is attached to the bottom of the canvas, which sags the mesh, otherwise the screen will not be effective without it.

Homemade fishing screen - easy and simple!

If you haven't changed your mind and still want to make a fishing screen, let's get started. This will require the following materials:

float made of foam;
a metal bar or, as they call it in another way, a bar;
wooden rail;
fishing line;
mesh fabric;
kapron thread or cord.

A good angler has in his arsenal many varieties of tackle, lures and other accessories for any fishing season. In addition, any professional angler needs to have such a fishing device as a fishing screen in their fishing gear.

Many fishermen have known him since early childhood. It is easy to make and does not require a large investment to make it.

Since not all fishermen have enough money to buy it in a fishing store, let's see how you can make a homemade fishing screen or, as it is called in another way, a fishing TV, right at home and save your hard-earned money.

In fact, you should not expect a big catch with the help of a fishing screen, but both adult fishermen and children love this device very much. With it, you can catch enough fish in your ear or just fry, but the most important feature of the fishing screen is that it does not pollute the fish habitat, that is, the reservoir, and does not harm the fish.

You can catch about the same amount of fish with this device as with a spinning rod or a fishing rod, but the only difference is that you cannot catch large fish with it. After all, the pleasure is not in what kind of fish you catch, but in the very process of fishing.

Stages of manufacturing a fishing screen

To make a fishing screen, you will need a square or rectangular frame. You can choose the sizes by eye. The dimensions depend on the depth of the reservoir and the place where you are going to throw it.
The float or top of the screen is made from a bamboo or wooden stick that needs to be varnished. This process is necessary so that the wooden structure does not swell in water. You can, of course, not varnish, but this can subsequently destroy the structure. The weight or lower part must be made of heavy materials to immerse the screen to the bottom of the reservoir. For the bottom of the fishing screen, you can use a metal bar. Then we cut the canvas from the grid to the size of the prepared frame in the lower and upper parts of the canvas and pull the cord. This must be done on each cell, or at least through one.
When you have a cooked frame, you need to fasten a mesh fabric to it using a strong thread. This is done in the following steps: first, we fix the end of the thread to the bamboo stick, then the mesh cell must be tied in other places with the help of a thread. And so it continues until the mesh canvas is completely fixed to our frame. A similar procedure must be done with a metal twig.
After that, from the side of the canvas, we skip the prepared thread in the form of a spiral, starting from a stick and ending with a bar, while not a single cell can be skipped. This is necessary in order to relieve the tension of the net under water, and during the raising of the net to the surface of the water.
We fix the cord on the stick in the middle, then we hook the float to it, for the manufacture of which foam plastic was used. The presence of a float is necessary in order to know where the fishing screen is located.

On a note: a net made from fishing line is the most catchy compared to a net made from twisted rope, while a net that was made from fishing line has a shorter service life than a net cloth.

Fishing Screen Installation Methods

There are two ways to install a fishing screen:

The first installation method is from the shore. In this case, you need to tie a rope to the screen body and throw it into the pond, and when you need to pull it out, it is enough to pull the rope towards you and the screen will come out.
The second way is from a boat. In this case, the screen is lowered to the bottom of the reservoir using a nylon thread with a float in any desired place.

It should be noted that in most cases the fishing screen is used from a boat in the middle of the reservoir. And remember that you should not abuse the capabilities of the fishing screen.

Screen fishing is a primitive and illegal tackle, but screen fishing is still considered effective among anglers. The availability of materials and ease of manufacture make this device widespread. Therefore, this tackle is very popular among fish hunters. Let's find out what it is and how to do it?

Among the numerous fishing tools, there are those that are so simple that they do not require special skills or skills. These tools also include a screen or, as it is also called, a TV for catching fish.

This device for fishing consists of the following parts:

Wooden lath or sealed tube.
Square or rectangular grid.
Metal bar-load.
Cord.
float.

As you can see, there is nothing complicated in this gear and it is easy to make it yourself.

Catching fish on the screen is easy and simple. It is enough to throw it into the intended place of parking or feeding fish and after a while get it with a catch.

Despite the fact that tackle is considered poaching, parts for its manufacture can be purchased at the store and made by yourself. This will not take the angler much time.

As already mentioned, the net is bought at a fishing store or a piece is cut off from an old unnecessary net. You also need to find a wooden rail and a metal bar.

In addition, to make a screen with your own hands, you need to have on hand:

roulette;
scissors and knife;
twine or thick fishing line;

Immediately you need to decide on the size of the TV. Usually its dimensions are not more than 1.5 by 1.5 meters. In addition, you need to choose the mesh size of the grid, which should correspond to the fish you plan to catch.

With the help of the screen it is convenient to catch live bait, and for this purpose a smaller mesh size is needed. If the goal of the angler is big fish, the cell size increases accordingly.

When starting to make a TV, you first need to cut the rail to the size of the grid. After that, mark at regular intervals on the rail the points where the “display” of the screen will be mounted. The bar at the bottom of the TV should be equal to the rail in length.

Having drilled holes at the ends of the rail, we attach the mesh to it with a fishing line or a strong synthetic thread. Then we attach the rod to the bottom of the net also with the help of a fishing line. Some use PVC tape to secure the net.

We tie a strong twine or a thick fishing line to the holes at the ends of the rail so that the made screen hangs on it. In the middle of this twine we knit a cord, at the end of which a large foam float is attached. It is needed to indicate the location of the TV, as well as to control the presence of fish on the screen.

Here's how to make a fishing TV with your own hands - simply and with a minimum of costs.

Catching fish on the TV is not particularly difficult. It is best to install the screen from a boat, although you can throw it into the water from the shore. To do this, you can use a kind of "rod" from any suitable rod or branch.

Tackle is placed at the place of feeding or migration of fish, at the border of aquatic vegetation, in small channels, and the like. To attract fish to the TV, some anglers tie some kind of bait in the center of the screen: a piece of cake, a small bag of bread, porridge, and so on.

There is a more original way to lure the fish into the net. This is an ordinary Christmas tree tinsel, pieces of which are tied in different places of the net and attract fish with their brilliance. In this way, you can catch predatory fish.

It must be remembered that tackle called "TV" or "screen" is considered poaching, and the angler using it can be fined.

Currently, many anglers refuse to use such gear. Nevertheless, this method of fishing attracts the attention of fishermen for various reasons.

Here are some of them:

Simplicity.
Availability.
Cheapness.
Mobility.
Versatility.

Given these reasons, we can confidently say that screen fishing will be used in Russian waters for a long time to come.