If you love roller skating, you will probably miss the thrill over time - after all, in addition to ordinary skating, there are various tricks that can be performed on roller skates, reaching the pinnacle of skill in the art of skating. The simplest stunt device that rollerbladers can use is springboard, which the roller can do on its own, using simple tools and improvised materials. In this article, we will tell you how to make a flat wooden springboard using a hacksaw for wood, a jigsaw, a drill and a screwdriver.

Instruction

1. Start with making springboard not too steep. First, draw a sketch in the form of a right triangle, the lower leg of which is 145 cm, and the side leg is 60 cm. The hypotenuse will be the immediate length springboard but. Take a sheet of birch plywood 24 mm thick, as well as 10 meters of boards 4 cm thick.
2. On the plywood, draw the outline of the triangle springboard and apply along the contour of the board. Saw off the corners from them so that they fit into a triangle. With a hacksaw, cut out boards of the desired shape for the longitudinal sides of the triangle, and then shorter ones.
3. Fasten the side frames springboard and with the help of a drill and self-tapping screws or screws. Do not make more than four holes with a drill at the frame attachment point. Also, do not use ordinary nails and a hammer for fastening.
4. Having made two triangles of sidewalls, cut out four transverse boards that you will fasten between the triangles. They will ensure the strength of the structure and allow you to even better secure the site. springboard and over the frame. Fasten the cross boards at right angles to the sloped slope line with self-tapping screws.
5. Now take a sheet of plywood of the desired length and width, according to your frame and its dimensions, adding 1 cm on each side. Attach the sheet to the frame with screws and a drill, making gaps between the screws by 10-12 cm.
6. To springboard became stronger, in its wide part, under the rise, strengthen the transverse board. To drop by springboard it was more convenient and safer, on the lower bevel touching the ground, reinforce a narrow metal strip 30 cm wide and 3 mm thick.
7. Fasten the steel strip with screws so that its front edge protrudes slightly from the edge of the plywood sheet. This will allow you to drive on without shaking. springboard from any surface. soak springboard protective impregnation and paint.

Straight trampoline

To begin with, let's start building springboards - flat and with a radius. The springboards themselves can be of almost any design: solid wood, metal with wood, and even concrete ... We will focus on the all-wood construction, and here's why: no special equipment is needed. tools, welding and other additional equipment. Of the tools you will need: a hacksaw for wood, an electric or hand drill, and screwdrivers. Find a jigsaw - make this micro-building much easier for yourself.

Let's start with flat run jumps: they are easier to build and will give you a little practice before making other elements of the site.

Flat springboards, despite the primitiveness of their appearance and design, are quite a necessary thing: especially for a start, it makes you understand the sensations of height and flight (even if symbolic).

In this case, there are no "standard" configurations. The ratio of the length and height (i.e. steepness) of such a springboard, in principle, can be anything, but you need to remember that a flat springboard with too much steepness will greatly dampen speed, and the sensations after such a “sticking” into an inclined plane are not very...

When marking, it is easier to calculate the slope in degrees: let's say a springboard with a curvature of 10 degrees. with a height of 40 cm is quite suitable for beginners. And on the springboard with a steepness of 25 degrees. and 1m high. you can do serious things.

Let's start with a sketch: let's say we build a springboard 145 cm long and 60 cm high - these dimensions provide it with an acceptable average steepness. For the trampoline you will need:

plywood: 1 sheet 24 mm or 2 sheets 12 mm, plywood is better to look for hardwood - birch, etc.

boards: 40 mm thick, total length 10 meters (2-3 floor boards will do). Width of boards - any.

Frame layout. I recommend drawing a triangle with a springboard plan directly on a sheet of plywood. Then lay the boards on the outline of the drawing (i.e. along its outline) as they will be located in the springboard frame structure and transfer the cutting lines to them. You will get marked blanks for the frame, cut off the excess on them with a hacksaw.

First, make longitudinal elements (long) and only then from the remaining pieces - transverse (short).

Frame preparation: fasten the sidewalls. We put the cut-off blanks of the longitudinal (which are long) parts on plywood according to the pattern (triangle); these blanks can be lightly attached to the plywood with long, thin nails so that they do not move during the assembly process. Then we put crossbars on top of them, drill them at the stitching points with a 4 mm drill and fasten them to the longitudinal parts using 75x7 mm self-tapping screws (75x8 mm) or screws 65-75 mm long. Make no more than 4 holes at each attachment point - a large number of them will not add strength, but, on the contrary, will only weaken the frame stitching point. Nails should not be used unambiguously - knots fastened with nails quickly weaken and loosen from monotonous loads.

Frame assembly. First you need to decide on the width of the springboard:

Based on the width, you need to make 4-5 blanks for the crossbars for the crate. Each must be attached to the sidewalls at right angles to the slope, for this it will be enough for two or three self-tapping screws 75-80 mm long with a board width of 15-18 cm.

Sheathe the frame with plywood. This is the easiest operation - measure the length and width of the top of the springboard, add an allowance of 1-2 cm on each side, after which you can cut.

Fasteners: depending on the thickness of the plywood - with self-tapping screws (screws) of the appropriate length, the distance between the fastening points is 10-12 cm. After the top is sheathed, the structure will become rigid.

The main thing - do not hammer the screws with a hammer.

Finishing. We put the crossbars in front of the springboard. You can strengthen it with braces and from below.

In general, the most important part of the work in the manufacture of any jumps, slides, etc. - Proper check-in. This is done as follows: fasten a steel strip 300 mm wide and 3 mm thick with M5 screws with a cone head (under the sweat) so that 10 cm of the strip protrudes before the start of the race. When the springboard rests on the asphalt, this free edge will bend itself as it should. The ride will be smooth and solid.

The finished springboard should be impregnated with water-repellent impregnation and painted. There are many such antiseptic impregnations, both Russian and imported.

The cheapest and most affordable option is to soak the entire tree with hot drying oil and paint it with oil paint.

13 cool ways to make a track, track, parking lot, slides, car wash, garage, road for kids with your own hands. All this can be done from ordinary materials that almost everyone has at home. Let's take a look at these creations.

1. Do-it-yourself foam (cardboard) track for children's cars.

Track for cars, which can be done with children and for children. Fast, clean, easy and economical. All we need is:

• white foam, if it is not there, then you can use a large cardboard, having previously painted it;
• decorative tape;
• scissors;
• wooden cubes, if they are not available, then you can use any building blocks that you have at home;
• brushes.

We paint wooden cubes with acrylic paint. Colors can be any, we have pastel colors of yellow, carrot, blue. We mark the route with a simple pencil, then paste over it with decorative tape. That's all, the track is ready. You can play with it at home, on the street. Easy to store it is flat, you can hide it under the bed or behind the closet.

2. Do-it-yourself car wash for cars from a cardboard box.

Cool idea for summer time. With such a car wash, you can play on the street, in the country, since you can really wash children's cars there. Children just love to play with water. And here you can spray cars from a spray bottle.

To make a children's toy, we need:

• cardboard box;
• cellophane to paste over the walls and floor of the car wash;
• felt;
• wooden bushings, and two toilet paper bushings;
• scissors, hot glue.

We start by cutting off the roof, one sidewall of the cardboard box, and on the opposite side we do something like a door. Next, let's start painting. It is necessary to paint over all the outer walls and the bottom of the box, so we will protect it from moisture.

After the box dries, glue the cellophane to the inside. You probably guessed that this will save the box from moisture and it will last longer.
We cut the felt and glue it to wooden bushings (you can also sticks), to toilet paper bushings. We attach everything to our car wash. Kids can play with this for hours.

3. Do-it-yourself children's road.

Very simple road from a cardboard box. All you need is time, desire and creativity. But seriously, cardboard, pencil, scissors, paint, brush.

From the box we cut out with trees, houses, and then color it all. Children will be happy to color everything, and at the same time we stimulate the development of creativity and fine motor skills at our little ones.

4. Racing track for children's cars.

Racing track for the descent of four cars at once. It is easy to make it with your own hands, and children will love it very much, because four cars can move along it at the same time. Both boys and girls will be able to figure out which car goes faster.

To make the track, we need:

• cardboard box;
• hot glue;
• paint, brushes.

Just lift the cardboard and the cars will rush down quickly. This is a great toy for home when it's bad outside. Older children will especially like it, because they love speed and movement.

Below is a slide made of a wooden board, more durable, large. You can't do without a dad. Stock up on material and call dad.

Detailed instructions with lots of photos in .

Children's fun for creative kids and parents. Everything is very simple, but very interesting. With such entertainment, it is advisable to take water-based paints to make it easier to wash soiled clothes.

5. Do-it-yourself parking for children's cars from shoe boxes.

A simple parking lot (garage) made from shoe box lids, toilet paper rolls and cardboard.

6. Large multi-level parking with a cardboard city.

Over such a structure it will be necessary to puff a little. The work is painstaking, but what a wonderful city for cars it turns out. There are trails and slides, multilevel parking. In a word, great!

Another very interesting version of cardboard crafts is a parking garage. These are the houses for cars you can make yourself, but also play with them. For those who decide to make such parking garages - a link to a site with a description and photos.

Other do-it-yourself car parks and garages made of cardboard, ideas for inspiration.

7. Do-it-yourself wooden parking for children's cars.

Cool parking for small children's cars. It is made of wood so it will last a long time. The safety of the child is also thought out - there are no sharp corners in it, they are all beveled. For those who decide to make such a parking, see the instructions and description.

8. Do-it-yourself road for cars.

This is perhaps the easiest way to make a children's track for small cars. You only need special tape and scissors. If desired, you can add plastic figures of a traffic light, a house, trees, in general, what you have at home.

Children's track, even the whole city. Detailed description You can view
Here, a children's road made of adhesive tape was glued to cardboard, thanks to which it can be moved around the house and even taken outside.
And here they glued adhesive tape in the form of a road directly to the floor.

And here we went even further, gluing adhesive tape directly to the sofa and carpet. Interestingly, many parents agree to this. But how fun and comfortable for children. If you do not have a special adhesive tape with an image of an asphalt road, then you can use colored tape or ordinary electrical tape. If desired, it can be marked.

9. Road for cars on an old wooden table.

If you have an unnecessary or old wooden table, then it can be turned into a track for children's cars. Mark the table with paper tape before painting. After painting, wait until it is completely dry. The road for children is ready.

Slide, parking, gas station on a wooden table with your own hands.

Large and wonderful table with game zones. How to make such a toy for children yourself, see

This version of the road for children's cars is convenient because you can draw it as you like and as much as you like. To do this, you need a piece of chalk and your or a child's imagination. To make such a game table for cars, you need to cover the table top of the old table with a special paint for chalkboards, on which you can draw with chalk. That's all the table for children's cars is ready!

10. Height meter in the form of a race track.

For little car lovers, parents can make such a bright stadiometer in the form of a race track. We mark the growth of the child with a typewriter, which is attached according to the Velcro principle. The road can be made of any width, with the number of lanes equal to the number of children. The photo shows that there are two children in the family. If you are interested in a stadiometer, then a full description of its manufacture can be viewed

11. Road for children's cars on the wall.

The road for cars can be made right on the wall in the children's room. Thus, we get an interesting design and play space for the child. The road itself can be made magnetic or made of felt, and magnets or Velcro can be attached to the cars, respectively.

12. Do-it-yourself carpet for cars made of fabric.

Rug-road made of felt with a surprise. He has a garage for three cars, these are pockets at the bottom. It is great that such a rug can be folded and it does not take up much space. It can be made of any size with any applications - mountains, trees, houses, hospitals, towers, skyscrapers, roads, slides, parking lots, various markings and all possible road signs. See this site for ideas and instructions with lots of photos.

13. Children's street track for small cars.

In the manufacture of such children's tracks for cars, you will need cement. You dig a shallow trench in the ground, fill it with cement, paint it with black paint, and decorate the entire site. This is an ideal playground for private houses and summer cottages.

Here are a few more options for outdoor play areas for boys from improvised material.

Children's town on the sand with a road for cars.

In conclusion, I would like to offer the most fun and funny way for a children's road for small cars. Children will not be bored, but dad or mom will get a wonderful massage and a portion of relaxation.

Thank you for reading our article to the end! Merry and happy day to you and your children!